RS-1 / RS-3 / RS-4 RS-00 (ADD-ON MODULE) 1 WAY SYSTEMS REMOTE ENGINE STARTING SYSTEM INSTALLATION INSTRUCTIONS INTRODUCTION CONGRATULATIONS on you
10 BASIC DOOR LOCK DIAGRAMS AFTERMARKET MOTOR/DOOR LOCK WIRINGREVERSE POLARITY DOOR LOCK WIRINGGREENGREENFUSEDFUSEDREDRED+12V+12VBLUEBLUE++868586858
11 “SMART TACHLESS” MODE Your CoolStart system includes a unique voltage monitor called “Smart Tachless” mode. This mode allows this unit to effic
12 TACH FINDER & USEFUL TIPS TACH FINDER MODE: This Tach Finder mode can assist in locating a Tach source for your installation. When followi
13 TACH PROGRAMMING & TACH SIGNALS INTRODUCTION Tach signals will vary in levels and frequencies depending on many factors including the type of
14 TIMED CRANK MODE This feature provides an easy method of starting the vehicle without locating an exact tach wire. The system uses a timed cran
15 DIESEL GLOW PLUG DELAY This feature provides a solution for diesel vehicles without having to connect to the Glow Plug-Wait to Start Circuit. Thi
16 OPTION PROGRAMMING To Engage Option Programming: 1. Open hood, If no hood pin switch is installed, then ground the Gray hood pin wire. Turn Ke
17 Option # Option Description TX Button #1 TX Button #2 Default Value TX Button #3 TX Button #4 9 Brown wire function Dome Light *Trunk pop* Pr
18 OPTION DESCRIPTIONS 2. Auto Lock Unlock: The option controls whether the doors will automatically lock/unlock on your vehicle when driving or wi
19 OPTION DESCRIPTIONS 9. Brown Output Wire Function: Trunk Pop or Dome Light Output This option controls how the Brown output wire of the unit f
2 TABLE OF CONTENTS Pre-Installation Considerations….………...……...………………………………………………………………..….………..2 Installation Cautions & Warnings………………………………
20 OPTION DESCRIPTIONS 17 OEM Interface (RS-00 Add on Model): This option controls the input selection for the Green Negative Start Trigger Wire.
21 TRANSMITTER PROGRAMMING Transmitter Programming: (Excludes RS-00 model without remotes) Notes: Remote Transmitters/Transceivers come pre-program
22 2 VEHICLE PROGRAMMING The RS-1, RS-3and RS- 4 series can be used for 2 vehicle operation. A single remote can control two independent vehicles w
23 MANUAL TRANSMISSION MODE MANUAL TRANSMISSION INSTALLATION: (PINK WIRE) After programming option #11 for manual transmission mode, the pink “Glo
24 JUMPER PIN DIAGRAMS Jumper pins are used to change/configure the operation of the on board multi-function output PINK WHITE wire and the Parking
25 ANTENNA DIAGRAM Antenna should be located at top of widow at least one inch away from metal surface. WINDSHIELDANTENNALOCATIONS DATA PORT Th
26 LOW CURRENT PLUG Orange/blackYellow/blackBlackWhiteRed/whiteOrangeBrownYellow/whiteGroundRUN (Ign 1)(-)Start Activation(-)(-)(-) OEM ArmParking
27 HIGH CURRENT PLUG 6 PIN HIGH CURRENT PLUGSTARTIGNSTART / IGN / ACCACCControlSTART 2IGN 2ACC 2Fuel A/C - HeaterPumpCoilJumper SelectDefault = IGN
28 REMOTE START DIAGNOSTICS If the system flashes the parking lights one to three times and doesn’t attempt remote, it means the following: 1 Parki
3 INSTALLATION CAUTIONS & WARNINGS FOR SAFETY REASONS, DO NOT INSTALL in vehicles with MANUAL TRANSMISSIONS.** If accidentally left in gear, a
4 WIRING YELLOW BLACK FOR NEGATIVE IGNITION OUTPUT: (Relay and/or Module not included ) YELLOW/BLACK858630 873rd IGN (If needed)IGN SW.ORANTI-THEF
5 WIRING TAN: (-) AUX OUTPUT (TRUNK POP) or DOME LIGHT ILLUMINATION OUTPUT This output is programmable for 3 modes of operation. See Programming Op
6 MomentarySwitchNew TURBO TIMER MODEGREENRS-00 EXPANSION (Default)RS-00 OEM INTERFACEGREENGREEN(Not included)(Aux ChannelAFTERMARKET1 sec. (-) pulse
7 WIRING GRAY: (-) NEGATIVE HOOD PIN SWITCH REQUIRED FOR PROGRAMMING Connect the Gray wire to a switch that is at ground when the hood is open. If a
8 RED WHITE: TACHOMETER INPUT When installing the system in Tach mode, this wire must be connected to a valid source of AC voltage. This wire allows
9 Crimestopper Door Lock Accessories: CS-6600DLM: Dual-relay plug-in module for Reverse Polarity, Positive, or Aftermarket Motors. CS-6500DLI: Plug-i
Kommentare zu diesen Handbüchern