CrimeStopper CS-2100 Betriebsanleitung PDF herunterladen

CS-2100

REMOTE CONTROL ALARM SYSTEM

INSTALLATION & OPERATING INSTRUCTIONS

*IMPORTANT INFORMATION: Primary and Optional Features

-PRIMARY: These are features that must be connected in order for the system to operate properly i.e. Siren, L.E.D.,

Power, Ground, Doorpin, etc.

-OPTIONAL: These are features to be connected only if desired or agreed upon by the installing dealer (i.e. Door

Locks, Starter Kill, Hood, Trunk, and Auxiliary Remote Output etc.) Optional features may require extra parts and/or

labor to install.

TECH SUPPORT

Mon-Fri 8:00 AM-4:30 PM Pacific Time

(800) 998-6880

www.crimestopper.com

[email protected]

INSTALLATION CAUTIONS & WARNINGS

BEFORE BEGINNING, check all vehicle manufacturer cautions and warnings regarding electrical service (AIR BAGS,

ABS BRAKES, AND BATTERY).

TO PREVENT A POSSIBLE DEAD BATTERY remove vehicle dome light fuse while working on the vehicle. MAKE

CERTAIN TO REINSTALL FUSE PRIOR TO TESTING FOR DOOR TRIGGERS.

DO NOT EXCEED MAXIMUM OUTPUT RATINGS! - SERIOUS DAMAGE MAY OCCUR. LIMITS FOR ALARM

FUNCTIONS ARE LISTED WHERE APPLICABLE. IF UNSURE ABOUT CURRENT LOAD, MEASURE LOAD WITH

AN AMP-METER.

REMOVE MAIN SYSTEM FUSE(S) before jump starting the vehicle or charging the battery at high boost.

This device complies with FCC Rules part 15. Operation is subject to the following

two conditions: 1) This device may not cause interference, and (2) this device

must accept any interference that may be received, including interference that may

cause undesired operation. The manufacturer is not responsible for any radio or

TV interference caused by unauthorized modification to this equipment. Such

modification could void the user's authority to operate the equipment.

1 2 3 4 5 6 7 8 9

Inhaltsverzeichnis

Seite 1 - CS-2100

CS-2100 REMOTE CONTROL ALARM SYSTEM INSTALLATION & OPERATING INSTRUCTIONS

Seite 2 - COMPONENT MOUNTING

COMPONENT MOUNTING DO NOT mount the control unit in the engine compartment. DO NOT Mount the control unit or wiring harness where they can become en

Seite 3

WIRING VIOLET WIRE: (+) DOOR TRIGGER INPUT Same as GREEN wire [below] except this wire is used for vehicles that show a positive voltage (12 volts) w

Seite 4 - OPTION PROGRAMMING

WIRING / PROGRAMMING 4 PIN SENSOR PLUG: WHITE WIRE: NEG. WARN AWAY *The Sensor supplied with the system does not require BLUE WIRE: NEG. TRIG

Seite 5 - OPERATION

BUTTON #1BUTTON #2 OPTION CHART * = DEFAULT Option # Option Description Selection Button 1 Button 2 1 Passive Arming ON or OFF OFF* ON 2 Aut

Seite 6

OPERATION EMERGENCY OVERRIDE/ VALET MODE If you have lost the transmitter or it stops working for any reason and the Alarm is armed, you will have to

Seite 7 - POWER DOOR LOCK WIRING

POWER DOOR LOCK WIRING +++

Seite 8 - (+) 12V POWER INPUT

87A8687308587A8630BATTERY+-IGNPROG/VALET BTNPIN SWITCH(+)POSITIVE DOORSWHOOD/TRUNK(-) NEGATIVERELAYPIN SWITCHOPTIONALSTARTER KILLLEDFUSEBOX+IGNITION&q

Seite 9

Kommentare zu diesen Handbüchern

Keine Kommentare

CrimeStopper CS-2100 Betriebsanleitung

Stöbern Sie online oder laden Sie Betriebsanleitung nach Auto Alarmanlage CrimeStopper CS-2100 herunter. CrimeStopper CS-2100 Operating instructions Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Auto Alarmanlage CrimeStopper CS-2100